#HOW TO WHITELIST A WEBSITE ON SONICWALL SOFTWARE#

This will be the exact same process as above with the second set of NextivaвЂ™s IP ranges.Д®nter the information below, then select Save to close the window.Д¬ontinue setup by selecting the following options from the drop-down menus: Select the Matrix view again, then select the arrow from LAN to WAN to enter the second IP range. Select Add or OK to save the first Access Rule.

Explicit 802.1p Value: 6 вЂ“ Voice (<10ms latency)ДЇigure 2-5: QoS For Voice Calls Configuration.

Explicit DSCP Value: 46 вЂ“ Expedited Forwarding (EF).

Select the QoS tab and use the drop-down menus to select the following options (Figure 2-5). Select the Advanced tab at the top of the window, then enter 90 in the UDP Connection Inactivity Timeout (seconds) field (Figure 2-4). Select the Destination drop-down menu, then select Create new networkвЂ¦Д®nter the information below, then select Save to close the window (Figure 2-2).Д¬ontinue setup by selecting the following options (Figure 2-3). On some versions of SonicWall, you may need to select Add on the following screen if a popup window does not display.

Select the Matrix view, then select the arrow from LAN to WAN (Figure 2-1). The Access Rules setting may also be under the Policies section on the left navigation pane. Select the Firewall tab, then select Access Rules.

Each rule will specify two different IP ranges for Nextiva service. Two access rules for LAN to WAN, and two access rules for WAN to LAN. To Enter NextivaвЂ™s Firewall Access Rules вЂ“ LAN to WAN:ДЄ total of four access rules will need to be created. Repeat steps 11 вЂ“ 12 for the LAN interface. Select the Advanced tab, usually located at the top of the window.Д¬heck the Enable Multicast Support checkbox (Figure 1-4). The label will be Default WAN (Figure 1-3). Select the Edit or Pencil icon next to the WAN interface. Select the Network tab, usually located on the left navigational pane. Select the Firewall Settings tab, usually located on the left navigational pane.Д®nsure the Enable Multicast checkbox is checked.Д®nsure that the Enable reception of all multicast addresses radio button is selected (Figure 1-2). To get to the settings below, you may need to also select SettingsВ depending on the model of SonicWall you have.Д¬heck the Enable Consistent NAT setting checkbox, then uncheck the Enable SIP Transformations checkbox (Figure 1-1).ДЇigure 1-1: Consistent NAT and SIP Transformations Select the VoIP tab, typically located on the left navigational pane. To Disable SIP ALG and Double NAT, and Enable Multicast:ДЄs a Network Administrator, log in to the SonicWall device through a web browser. Please ensure a Network Administrator familiar with the SonicWall device configures the settings below.

#HOW TO WHITELIST A WEBSITE ON SONICWALL SOFTWARE#

NOTE: Due to the variety of software versions, the instructions below may not be entirely accurate, though should stay relatively consistent.

Firewall Access Rules: Entering NextivaвЂ™s Firewall Access Rules ensures that all traffic to and from NextivaвЂ™s servers is allowed.

Multicast: Enabling Multicast support ensures that simultaneous outbound calls are routed properly to prevent call failures, and inbound calls going to multiple devices (as in a Call Group) are routed properly.

Consistent NAT: Enabling Consistent NAT prevents one-way audio, failed transfers, dropped calls and Call Group inconsistencies.

SIP ALG: Disabling SIP ALG (SIP Transformations) prevents one-way audio, phone deregistration, and failed incoming calls.

The configuration steps below solve a number of issues: This version of Sonicwall is not recommended, but in many cases can be supported. The Enhanced OS is more consistent and reliable than the Standard OS, but there have been a few revisions of the Enhanced OS that have similar problems as well. The Standard OS can frequently have issues with blocking/disallowing traffic that should normally be accepted.В This version of the Sonicwall is not recommended or supported. There are two versions of operating systems on SonicWall devices. SonicWall devices are a relatively common business class hardware firewall/router device that allows for multiple WAN and LAN inputs, as well as other advanced features not commonly available for consumer class routers. To skip to the section to enter NextivaвЂ™s Firewall Access Rules click here. To skip to the section to enable Multicast click here. To skip to the section to prevent Double NAT click here. To skip to the section to disable SIP ALG click here.

How to whitelist a website on sonicwall